Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Mr-Glass Fence Installation: The Austin Owner’s Guide
We install and replace Mr-Glass fence panels, posts, and hardware throughout Austin, and a full fence installation typically runs $3,500 to $9,000 depending on linear footage, existing post condition, and gate hardware. Most Mr-Glass fence failures we see in Austin come down to two things: UV-brittled glass clips and posts that shifted in clay soil. You’ll usually notice it as a panel that rattles in the wind, a glass pane that’s cracked but still sitting in the frame, or a gate that drags against the latch plate. Isaac Pruett and our crew have pulled hundreds of Mr-Glass panels apart in Austin driveways, and we can tell you pretty quick whether you need a part swapped or a full section rebuilt.
Which Mr-Glass Models This Applies To
Mr-Glass fence systems run two main lines: the original aluminum-framed glass panels (sometimes sold as the “Clearview” series) and the updated “Horizon” line with thicker 10mm tempered glass and a deeper bottom channel for drainage. The quickest way to identify your part: look at the inside corner of any panel frame for a stamped serial prefix, “MG-CV” for Clearview and “MG-HZ” for Horizon. If the stamp is worn off, measure the glass thickness at the edge. The original panels hold 8mm; the Horizon runs 10mm and weighs noticeably more per linear foot. That difference matters because Horizon glass won’t seat correctly in Clearview channels, and we’ve had homeowners buy a single Horizon panel off a liquidator site, only to find the clip spacing is off by 3/8 inch.
For Austin specifically, we stock genuine Mr-Glass clips, bottom channels, and post caps on the truck, but we’re honest about the aftermarket option. When a panel is discontinued or the lead time on OEM glass stretches past six weeks, we use equivalent tempered glass from a Texas supplier that meets the same 10mm spec. Mason Remodeling Co Austin is an independent service provider, not affiliated with Mr-Glass, so we’ll tell you exactly what fits and what just looks like it might fit.
Styles & brands we work with
Signs Your Mr-Glass Fence Installation Is Failing
- Panel rattle in the wind. The rubber glazing gasket inside the frame channel has compressed or dry-rotted after a few Austin summers. The glass moves a few millimeters, and the panel sounds loose every time a gust hits it.
- Fogging between glass panes. If you have double-glazed Mr-Glass panels, the seal between panes has failed. In Austin humidity, that trapped moisture becomes permanent haze you can’t wipe off, and the panel loses its thermal and acoustic value.
- Bottom channel standing water. Mr-Glass frames are designed to drain, but dust, pollen, and the occasional construction debris clog the weep holes. Water sits in the channel, then the aluminum starts oxidizing from the inside where you can’t see it.
- Post lean or gate misalignment. Austin’s expanding clay soil heaves every wet spring and contracts every dry August. Posts that weren’t set deep enough or lacked proper concrete footings lean gradually until the gate no longer lines up.
- Hairline cracks radiating from the clip point. Tempered glass gives at stress points. If a panel was installed with the clips over-torqued, or if the frame was bent to fit a sloped grade, you get spider cracks that grow until the pane finally gives way.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Austin, Mr-Glass fence installation runs $3,500 to $9,000 for a typical residential job. A partial repair, like one or two panels with new clips and new glazing gaskets, lands on the lower end. A full fence with new posts set in concrete, all panels replaced, and a gate rebuilt with fresh hardware goes toward the top of the range. Our written price includes all parts, labor, post-hole drilling, concrete, haul-away of the old panels, and a workmanship warranty. Here’s how a typical Austin job breaks down:
| Scope | Typical Austin Price Range |
|---|---|
| Single panel replacement (glass, clips, gasket, reset) | $600 – $1,400 |
| Two to five panels, existing posts reused | $1,500 – $4,200 |
| Full fence, new posts and concrete footings | $4,500 – $9,000 |
| Gate rebuild with new self-closing hinges and latch | $900 – $2,200 |
What drives the range, honestly, is post condition. If the existing posts are solid and plumb, we reuse them and the job gets cheaper. If they’re leaning or the concrete footings are undersized, we’re digging new holes, and that’s real labor in Austin limestone. You get a written line-item price before any work starts, and the 365-Day Done Right Promise covers the installation for a full year from completion. If something’s not right, we come back and fix it at no charge.
DIY or Call Us?
There are two things an owner can safely check without calling anyone. First, look at the weep holes along the bottom of the frame and clear them with a pipe cleaner or compressed air if they’re blocked. Second, inspect the clip screws at the frame corners. If they’re loose, snug them with a hand screwdriver. Do not use an impact driver on Mr-Glass clips. Tempered glass under point-loaded pressure fails violently, and one over-torqued clip can send a shower of glass cubes across your yard.
Beyond those checks, leave it to a professional. Removing a tempered glass panel from its channel without shattering it requires two people, rubber shims, and patience. Setting posts in Austin soil means drilling through limestone more often than not, and a homeowner-grade auger won’t always get there. If the gate is sagging and dragging, the fix is usually re-shimming the hinge posts, not just raising the latch. Call (903) 623-1966 and we’ll walk you through what you’re seeing before we ever set foot on the property.
FAQs
In our experience, a Mr-Glass fence installation with properly set posts and intact gaskets lasts 15 to 25 years in Austin. The aluminum frame itself won’t rust, but the glazing gaskets, post footings, and gate hardware all have shorter lifespans, usually 8 to 12 years, depending on sun exposure and how much the soil moves under your specific lot. Call (903) 623-1966 if you want us to inspect what’s actually failing on your fence.
No. Tempered glass cannot be cut, drilled, or patched once it’s been manufactured. A cracked panel is a replacement, period, and driving around with one that’s spider-webbed is a liability risk if it finally lets go. The good news is a single panel replacement is usually much cheaper than people expect, especially if we can reuse the frame. Call (903) 623-1966 for an exact price on your panel size.
A one or two panel replacement is usually a three to four hour job if the posts are healthy. A full fence with new posts takes two to three days, plus a day for concrete to cure enough to hang the glass. The posts are the schedule, not the panels. Call (903) 623-1966 and we’ll give you a straight timeline after we see the fence.
We stock the common clip sizes, gaskets, bottom channels, and post caps for both the Clearview and Horizon lines on our truck at all times. OEM glass panels and full replacement posts usually come from our Texas supplier within two weeks. You won’t need to order anything yourself, and we don’t push aftermarket glass unless the OEM panel is truly discontinued. Call (903) 623-1966 and tell us what’s broken. We’ll figure out what it actually needs.
Written by Isaac Pruett, Owner, Mason Remodeling Co Austin at Mason Remodeling Co Austin, serving Austin and nearby areas.
