Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Austin Owner’s Guide
CGI fence installation in Austin typically runs $3,500 to $9,000 for a full perimeter job, with most homes falling in the $4,500 to $6,500 range for standard lots. We stock CGI-compatible posts, rails, and mounting hardware on our trucks, which means most repairs and sections go in the same week we look at them. You’ll usually notice the problem the hard way: a gate that suddenly drags, a post that leans after a storm, or a section of fence that’s pulling loose from its hardware along the property line.
We’re an independent Austin contractor, not affiliated with CGI itself, but we’ve worked with their fence systems long enough to know what fails and what doesn’t. If you’ve got a CGI product that’s sagging, rattling, or separating at the fasteners, here’s what you need to know before you spend a dollar.
Which CGI Models This Applies To
We install and repair fencing built from CGI’s steel and aluminum panel systems, including their commercial-grade corrugated metal panels and the lighter residential lines that show up on a lot of newer Austin builds. The compatibility gotcha with CGI fencing is the post and rail channel system: CGI panels are designed to sit inside specific channel dimensions, and a fence built with mixed aftermarket channels will bind, rattle, or work loose at the fasteners. If your existing posts have a stamped CGI logo or a part number etched near the base, we match to that series. If the tag is gone, we measure the channel width and panel gauge before ordering anything.
On the OEM versus aftermarket question: we use OEM CGI panels when the fence is still under a manufacturer warranty or when an HOA requires the exact match. Quality aftermarket equivalents from our supplier network work fine for older fences where the warranty has lapsed, and they usually land 15 to 20 percent under OEM pricing. We’ll show you both numbers before you commit.
Styles & brands we work with
Signs Your CGI Fence Installation Is Failing
- Posts leaning after rain or wind. Austin’s clay-heavy soil expands and contracts through the wet-dry cycle, and posts set without adequate concrete depth will shift over time. A lean of more than an inch or two means the footing has failed, not just the post.
- Gate dragging or binding at the latch. This usually means the hinge post has moved out of plumb, or the gate hardware is wearing against the heavier steel panel. Continuing to force the gate open accelerates both problems.
- Panels rattling in the channels. CGI panels rely on a snug fit inside the post and rail channels. When fasteners loosen or channels spread, the panel chatters in the wind and the noise travels across the whole yard.
- Rust bleeding from fastener points. Austin’s humidity and the occasional hard freeze-thaw cycle punish exposed hardware. If you see rust streaking from screw heads or brackets, moisture has gotten behind the finish and the metal is deteriorating from the inside out.
- Visible gaps between panel and post. Warped or undersized panels shrink in heat and never seat right again. This is common on fences built with mixed components from different suppliers.
If you’re seeing any of these, the sooner you address it the cheaper it gets. The failing part rarely improves on its own.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
CGI fence installation in Austin falls between $3,500 and $9,000, with most full replacements on standard city lots landing around $4,500 to $6,500. Here’s where the money goes:
- Full perimeter CGI fence installation: $3,500 – $9,000
- Single section or gate repair: $400 – $1,200
- Post replacement (concrete footer repair): $150 – $450 per post
- Gate hardware and alignment: $200 – $600
The range depends on linear footage, panel gauge, soil conditions at the post holes, and whether we’re reusing existing posts or setting new ones. Every quote is a written price before work starts, covering materials, labor, disposal of the old fence, and the warranty on our workmanship. If a repair or installation fails within 365 days of completion, we return and make it right at no charge. No disputes, no conditions.
DIY or Call Us?
You can safely inspect a failing CGI fence yourself: check for loose screws, look for water pooling at post bases, and note whether gates are still square in their openings. That’s useful information to have when you call us. What you shouldn’t do is try to reset a leaning steel post or rehang a heavy CGI gate on existing hardware. Steel panels are unforgiving when they shift, and a post under tension while you’re digging around its footing can drop without warning. We’ve seen homeowners get hurt trying to muscle a 70-pound gate back onto a hinge that gave way.
Call (903) 623-1966 and tell me what’s wrong with it. We’ll figure out what it actually needs.
FAQs
A properly installed CGI fence with set concrete footers and galvanized or powder-coated hardware typically lasts 20 to 30 years in Austin, though post footings may need attention around the 15-year mark if the soil is especially expansive. Call (903) 623-1966 and we’ll assess your specific fence at no charge.
Yes, most failing CGI fences need only section, post, or gate repairs rather than a full replacement, and we quote the repair honestly when that’s the better option. If the repair cost would exceed half the price of new, we’ll tell you that too. Call (903) 623-1966 for a straight answer.
Most full CGI fence installations on Austin lots take 2 to 4 working days from post-setting to final gate adjustment, with concrete cure time factored in. Single-section repairs are usually finished in a day, which gives us room to match to CGI’s channel and gauge specs the first time, so you don’t pay for rework. Call (903) 623-1966 for a timeline on your specific fence.
Yes, we stock CGI-compatible panels, post channels, fasteners, and gate hardware in common sizes, and we can usually swap a failed section the same week we diagnose it. We’re an independent Austin contractor, so we also carry quality aftermarket equivalents from our supplier network, including brands we trust alongside our other work like KraftMaid cabinets, Cambria, and Silestone surfaces. Call (903) 623-1966 and we’ll match what you have.
Written by Isaac Pruett, Owner, Mason Remodeling Co Austin, serving Austin and nearby areas.
