Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Fence Installation: The Austin Owner’s Guide
PGT fence installation in Austin typically runs $3,500 to $9,000, depending on linear footage, the PGT product line you have, and what the ground is doing under your posts. We stock PGT-compatible aluminum fence panels and hardware on the truck, so a single-section replacement can often be handled in the same trip. Most Austin homeowners discover they need us the hard way: a gate that starts dragging, a post that leans after a heavy rain, or a panel that came loose during one of our spring wind events.
If your PGT fence is sagging, rattling, or a gate won’t latch, the fix usually comes down to the hardware, the post footing, or a panel that was never properly shimmed. Tell me what’s wrong with it. We’ll figure out what it actually needs.
Which PGT Models This Applies To
PGT makes several aluminum fence lines, and not every part swaps between them. The most common we run into around Austin are the PGT Industrial and PGT Commercial series, which use a heavier extrusion than the residential line. You can tell them apart by measuring the picket profile: the Industrial line carries a 5/8-inch square picket, while the residential panels use a slimmer 1/2-inch profile. The gate hardware is not interchangeable between the two.
Flip a panel over and look for the PGT stamp on the bottom rail. If it’s missing or faded, measure the rail width with a tape measure before you call us. The replacement brackets we use are OEM-spec PGT weather-guard brackets, which hold up better in Texas UV than the generic parts you’ll find at a big-box hardware store. We also keep aftermarket equivalents on hand for discontinued PGT panels, but we’ll tell you upfront when we’d rather use OEM.
Note on the brand relationship: Mason Remodeling Co Austin is an independent service provider. We install and repair PGT fence systems, but we are not affiliated with PGT and we do not speak for their warranty program.
Styles & brands we work with
Signs Your PGT Fence Installation Is Failing
- Gate drags or catches on the latch side. The most common cause in Austin is clay soil expansion after a wet spring. The post shifts, the gate goes out of square, and the latch no longer lines up. We reset the post and rehang the gate rather than forcing the hinges to compensate.
- Panels rattle in the wind. PGT uses screw-set brackets that can work loose over time. Loose brackets let the panel bounce, which wears the screw holes oblong. Once the holes are ovaled, tightening doesn’t hold; we replace the bracket and collar.
- Post leans at the base or concrete cracks around the footing. This is a footing depth issue, often from an older installation that never went below the frost line. In Austin, the bigger problem is expansive clay. We dig to 24 inches minimum and backfill with fast-setting concrete for a post that won’t move.
- Rust streaks under the rails. PGT panels are aluminum, so the panel won’t rust; the hardware can. If you see orange staining, the lag bolts or gate hinges are galvanized steel and have started to oxidize. We swap them for stainless hardware and the stains stop.
- Pickets shift side to side. The internal clips that hold pickets in the rail channel can snap when the panel is over-stressed, usually from a falling limb during an Austin ice storm. We can punch the broken clips out and rebuild the rail without replacing the whole panel.
Replacement Cost & What’s Included
For a full PGT fence installation in Austin, the range is $3,500 to $9,000 installed. That variance comes down to total linear feet, gate count, whether panels need to be matched to an existing PGT color (white and black are the most common, custom colors cost more), and what the ground looks like when we start digging. Rocky Hill Country soil is slower to auger than East Austin clay, and that shows up in the labor line.
Every quote you get from us includes the parts, labor, concrete, hardware, and clean-up in one written price before work starts. If we find a rotted line post that has to be pulled and reset, the price doesn’t move; that’s covered in the initial quote. Our installation work is covered in writing, and if something isn’t right within 365 days of the completion date, we return and fix it at no charge.
| SCOPE | PRICE RANGE (Installed) |
|---|---|
| Full PGT Fence Installation, Austin | $3,500 – $9,000 |
| Single Panel Replacement (matched PGT color) | $380 – $650 |
| Gate Adjustment / Rehang | $250 – $475 |
| Post Reset (single post, new concrete) | $350 – $700 |
| Hardware Swap (stainless upgrade, entire fence) | $600 – $1,400 |
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Here’s the honest split. You can tighten a bracket, re-lube a gate hinge, or mark a leaning post and watch it over a few weeks. Those are checks and basic maintenance, and there’s no danger in them. What you should not do is pull a PGT post and reset it yourself without the right auger and leveling setup. A post that is not perfectly plumb magnifies the problem across every adjacent panel, and once the rails are bolted in, you are fighting the whole system.
The most common DIY failure we see in Austin is forking out for panels before confirming the post layout is square. Measure twice and still call us if the numbers don’t line up. This isn’t the kind of work someone gets right on a YouTube tutorial the first time, especially with a heavy gate in the mix. Call (903) 623-1966 and we’ll price the job from photos before we ever roll a truck.
FAQs
A PGT aluminum fence installed properly will last 20 to 30 years in Austin. The panels themselves are lifetime material; the failure points are the hardware and the post footings. Our installs use stainless hardware from day one, which is the number one thing that determines whether the fence looks the same in year ten as it did in year one.
Call (903) 623-1966 for an exact quote on your layout. Estimates are free.
Yes, in most cases. We repair single panels, rehang gates, reset posts, and swap hardware without touching the rest of the fence. The question is whether the damage is structural or hardware-level. If the panel extrusion is bent or creased, replacement is cheaper than trying to straighten it. We’ll show you the difference before we recommend anything.
Call (903) 623-1966 and describe what you’re seeing. We’ll tell you straight what it needs.
Most complete PGT fence installations in Austin take from two to four days on site. That covers demo of the old fence, augering the new post holes, setting posts in concrete, and hanging panels on day three or four. Weather and soil conditions can extend that, but you’ll have a written schedule before work starts.
Call (903) 623-1966 to get a firm timeline for your specific yard.
Yes. Our trucks carry PGT-compatible brackets, stainless hinge sets, picket clips, rail stock, and fasteners as standard inventory. If we’re doing a single-panel repair, we usually bring the panel with us. If your fence is a custom PGT color, we order the matched panel and schedule the install when it arrives.
Call (903) 623-1966 with the panel measurements and color, and we’ll confirm we have it before we schedule.
Ready to Get the Fence Fixed Right?
If your PGT fence is failing in Austin, the fastest path to an honest answer is a phone call. You’ll talk to a real person, not a call tree. We’ll ask for the measurements and a couple of photos, give you a written price, and put Isaac Pruett and the crew on the schedule. Every technician who comes to your home is background-checked, identity-verified, and arrives in a marked uniform with a photo ID at the door. That’s the Threshold Standard, and it applies to every job we do, from a single gate hinge to a full fence replacement.
Call (903) 623-1966 for a free estimate today.
Written by Isaac Pruett, Owner, Mason Remodeling Co Austin at Mason Remodeling Co Austin, serving Austin and nearby areas.
